The use method of turning over nursing bed is introduced, come and collect!

TIME：

2023-08-30

How to use the turn-over nursing bed? Let's take a look at it briefly.

1. Position adjustment of the body: hold the head control handle tightly to release the self-locking of the gas spring, extend its piston rod, and drive the head bed surface to slowly rise at the same time. When it rises to the required angle, release the handle and the bed surface will be locked in this position. Similarly, hold the handle tightly and apply force downward to lower the thigh bed. The lifting of the foot bed is controlled by the foot position control handle, make the pull pin out of the positioning hole and lower it by its own weight. When it reaches the required angle, release the handle and the foot bed surface will be locked in this position. Coordinated use of the control handle and the rocker handle can enable the patient to obtain various postures from lying down to half lying down, bending legs, sitting flat and sitting upright. In addition, if the patient wants to lie on his side in the supine state, first pull out the bed head on one side, turn down the side guardrail, press the control button on the outside of the bed surface with one hand to release the self-locking of the side gas spring, extend its piston rod, and drive the side bed surface to slowly rise. When the control button is released to the required angle, the bed surface is locked in this position, and the side posture is completed from the surface. Note: Use the same operation in reverse.

2. Use of the defecation device: Rotate the defecation handle clockwise to automatically open the defecation hole cover. At the same time, the toilet carrier is automatically sent to the patient's hip along the horizontal direction. The patient can defecate or clean the lower part. Rotate the defecation handle counterclockwise to close the defecation hole cover and keep it flush with the bed surface. At the same time, the toilet bowl is automatically sent to the operator side so that the nursing staff can be taken away for cleaning.

3. Use of the guardrail of the turn-over nursing bed. Hold the top edge of the side guardrail horizontally, lift the turn-over nursing bed vertically by about 20mm, and turn it down 180 degrees to put down the guardrail. After the patient turns over the nursing bed, lift the guardrail up 180 degrees, and press it vertically to complete the lifting of the side guardrail. Note: The foot barrier is managed in the same way.

4. Use of living table: align the opening of the plastic part on the back of the living table with the upper side of the side guardrail and press it down. Hold down the guardrail with one hand and lift the working table with the other hand to start unloading.

5. Use of infusion hanger: The infusion hanger can be used no matter the bed surface is in any state. When using the infusion hanger, first twist the two sections of infusion hanger into one piece, then bend the hook under the infusion hanger and aim it at the horizontal tube above it. At the same time, the hook head above is aligned with the round hole of the tube above the side guardrail to be used, and the infusion hanger is removed.

6. The use of the brake: when pressing the brake with your foot or hand, it is braking, and when you lift it up, it is released.

7. Use of seat belts: When the patient uses the bed or needs to change the state, the seat belt must be fastened (the tightness of the seat belt is appropriately adjusted according to the individual) to prevent danger.

8. Operation of foot washing device: when the foot bed surface is level, adjust the thigh position handle and lift the thigh bed surface to prevent the patient from slipping off; Hold the foot position control handle tightly, put the foot position bed surface in the appropriate position, turn down the foot position movable board, shake the thigh position handle to keep the foot position movable board level, and put it on the water basin to wash feet. After washing the feet, remove the basin, the foot of the movable plate, reset to the original place. Grasp the foot control handle and lift the foot bed to the horizontal position.

What is the structure and performance of the turn-over nursing bed?

What is the function of the turn-over nursing bed?

From May 14 to 17, the 87th CMEF Medical Devices Exhibition was held at the National Convention and Exhibition Center (Shanghai). Zhejiang Medster Medical Device Technology Co., Ltd. was invited to participate in the CMEF medical device exhibition. At this exhibition, two absolutely innovative products of Medster Medical Device Technology Co., Ltd., "Suitable for Old Bed" and "Ergonomic Wheelchair", made their debut, which attracted wide attention and praise.

Zhejiang Medster Medical Device Technology Co., Ltd. was established in 2022. It is a comprehensive enterprise integrating the research and development, production and sales of rehabilitation aids and medical device products. It has registered branches in Hengshui, Hangzhou, and Shenzhen. Responsible for the company's brand operation, product development, sales and after-sales service business. The company's main products include rehabilitation nursing beds, medical beds, manual electric wheelchairs, anti-bedsore air mattresses, atomizers, breathing masks and masks. The company has successively obtained the registration certificates of electric hospital beds, rehabilitation nursing beds, wheelchairs, anti-decubitus air mattresses, atomizers, breathing masks and other products. Its subsidiary Hebei Ruilangde Medical Equipment Group Co., Ltd. is a national smart health elderly care application pilot demonstration enterprise, a national e-commerce demonstration enterprise, a member unit of China Rehabilitation Aids Association, a Hebei Province Rehabilitation Aids Application Demonstration Unit, and Hebei Medical Equipment Vice President Unit of the Association, Hebei Welfare Foundation Love Enterprise.

Since its inception, the company has adhered to the principle of "quality for survival, innovation and development"

A comprehensive enterprise integrating R & D, production and sales of rehabilitation aids and medical equipment products.

Medster's global layout has been effective, with overseas business breaking tens of millions in 2 days.

Recently, Zhejiang Medster Medical Device Technology Co., Ltd. released sales data for overseas markets during the membership day event. Data show that during the membership day, sales exceeded 10 million in two days, an increase of 150 percent over the same period last year; among them, the export sales of star products represented by the Medster medical sector increased by 264 percent compared with the same period last year, and the export sales of star products represented by the maidesite lifting table series increased by 145 percent compared with the same period last year. Judging from the data, Medster's product potential has begun to be gradually released overseas.

Nursing bed installation steps is what?

Nursing bed installation steps is what? 1. The nursing bed casters are equipped with two brake brakes, and the two casters with brake brakes are installed diagonally in the screw holes on the bed legs of the bed frame; then the remaining two casters are installed on the other two base legs In the screw hole. 2. Installation of the rear bed surface: connect the rear bed surface with the bed frame with the rear frame pin, and then lock the pin with the split pin. 3. Installation of the head of the nursing bed: align the head of the bed with the holes on both sides of the back bed surface and insert it, and tighten the fastening screws on both sides.

ZHEJIANG MEDITSTER MEDICAL DEVICE TECHNOLOGY CO., LTD

A comprehensive enterprise integrating R & D, design, intelligent manufacturing and sales of rehabilitation aids and medical device products.

Hangzhou Headquarters

Telephone:0571-87653297
Address: 5th Floor, Block C, Building 1, Kaichuang Technology Park,

No. 98, Liuzhe Street, Cangqian Street, Yuhang District,Hangzhou City,

Zhejiang Province

Shenzhen Operation Center

Telephone:400 0091 913
Address: 1703-1, Building 6, Tianan Yungu Industrial Park Phase II (08-07), Gangtou Community, Bantian Street, Longgang District, Shenzhen

Hengshui Operation Center

Telephone:0318-5201810
Address: 12th Floor, South of Thunder Building, Intersection of Zhonghua Street and Shengli Road, Taocheng District, Hengshui City, Hebei Province

Factory

Telephone:400 009 1913
Address: Medster Boutique Factory, Zhongkuang South Road, High-tech Industrial Development Zone, Jing County, Hengshui City, Hebei Province

Business License